Select your country
It’s easy to build a swing that’s fun for your kids to play on, by following these clear step‑by‑step instructions.
This swing looks great in every garden, thanks to the use of sustainably produced wood. The uprights are about 70 x 70 mm thick, and the top bar is about 70 x 140 mm, which ensures a sturdy structure. Make sure when you’re building your swing that it’s stable enough to play on safely. And provide a soft surface under the swing, so children won’t have a hard landing if they fall off the swing.
- Eye bolts
- Nuts size M12
- Snap hooks
- Garden wood or hardwood:
Beam thickness: uprights 70 x 70 mm, top bar 140 x 70 mm, cross-pieces 150 x 22 mm. Seat size: 450 x 250 x 22 mm.
Build the swing with a height, width and depth of 270 cm. Don’t forget that the uprights need to have a total length of 310 cm, because they will be recessed into the ground by an extra 40 cm to ensure the swing is stable.
We’ll start by positioning the 2 uprights, each with a length of 310 cm, on the left side at an angle of 60°. The two uprights, together with the width at the base which is also 310 cm, form the sides of an equilateral triangle (all three sides are the same length).
To allow us to assemble the uprights before we fit the top bar, we’ll make a spacer (A) with the same cross-section as the top bar. This spacer ensures that when we assemble the top bar, it fits precisely into the opening between the tops of the uprights.
Make the tops of the uprights fit neatly, saw the top ends off at an angle of 60°. Place the spacer between the uprights and fit the upper cross-piece in place. Saw the upper cross-piece (E) once you have positioned it so the top bar rests on it when you remove the spacer. Fix the cross-piece in place using four nuts and bolts, with washers between them. Secure each nut with an extra locknut, and tightened in the opposite direction to the nut.
To prevent the swing from twisting and bending, we insert an extra (lower) cross-piece (B) with a width of 22 x 150 mm between the uprights. This will hold the diagonal support (C) in place, on which the top bar (D) will rest. We’ll make a supporting structure like this at both the left and right sides of the swing.
Assemble the right upright with the upper and lower cross-pieces in the same way. This is a mirror image of the left upright, with the cross-pieces on the inner side of the swing.
Fit the top bar into the openings at the tops of the uprights, and drill holes through the top bar and the upper cross-piece. The cross-pieces are fitted on the inside of the swing. Fix the top bar to the uprights together with nuts, bolt and washers. Finally, fit the extra locknuts and tightened in the opposite direction to the nuts. Do the same on the right side of the swing.
Take a 150 x 22 mm plank with at a length of about 60 cm and saw each end off at an angle of 45°. Then fit the two diagonal supports under the top bar at both the left and right sides, and secure the top bar in place with nuts, bolts and washers.
To give the uprights extra stability, we’ll fit a stabilising plank to the two uprights at each side. Here again we can use planks measuring 150 x 22 mm.
For safety, you have to dig the swing uprights into the ground. Before you do this, screw a number of bolts into the bottom of each upright, so the uprights are firmly anchored after filling the holes with concrete mix.
Use a narrow spade or a post-hole digger to make a narrow hole with a depth of about 40 cm. You can fix the uprights in place with concrete mix, made of 1 kg of coarse sand, 1 kg of gravel and 0,5 kg of cement. You can also use quick-drying mortar mix – tip this into the hole directly from the bag and pour some water over it.
When you’re pouring the concrete mix, make sure the uprights of the swing are properly aligned. Use a spirit level to check that the top bar and the stabilising planks are horizontal and that, together with the uprights, they are properly aligned and parallel with each other. Finally, stamp the ground around the four uprights firmly in place.
Fit the eye bolts to support the swings to the top bar, evenly spaced from the middle of the top bar with gaps of about 50 cm between them. Drill the holes for the four eye bolts. Secure the bolts with nuts, bolts and washers, and fit extra locknuts, tightening these in the opposite direction to the nuts. Fit the eye bolts in line and tighten them using a screwdriver through the eyes of the bolts.
Use two planks (125 x 22 mm) with a length of 450 mm for each seat of the swing. Fit these together using similar planks with a length of 250 mm across and underneath the ends of the seats. That gives us seats measuring 250 x 450 mm. Drill four holes through the seats for the supporting ropes. Pass the ropes in a big loop through the snap hooks and through the holes in the seats, and tie four strong knots under the seats. Make sure the knots are big enough to support the weight of the seats and their occupants. The snap hooks make the ropes easy to fit and to remove later if necessary.
Andke samm-sammulisele juhisele hinne.
How to make a swing
What tools do you need?
Nõuanded tööriista valikuks